Austin Concrete CompanyAustin Concrete Company

Concrete cutting in Austin MN - clean, straight openings planned around what's inside

Need an opening in a slab, a doorway in a wall or a cracked section out? We scan first, then saw clean, straight lines.

A paved backyard patio with a wooden pergola, outdoor chairs, stone walls and a hanging chair.

What does concrete cutting involve, and what sets the price?

Concrete cutting in Austin, MN means sawing straight lines through a slab or wall, or core drilling round holes for pipes, drains and conduit, so you get a clean opening or a section out without breaking up the concrete around it.

Most cutting calls I get come from someone who needs a trench for a drain line, an opening in a basement wall, or a bad section sawed out so we can pour a new driveway or patio against a clean edge. The price mostly turns on how thick the concrete is, how much steel is in it, how many feet we're cutting and whether you want the pieces hauled off. The schedule turns on utility locates and any city approval, and your written estimate shows where the money goes. When a cut needs a permit, we handle the paperwork and set up the inspections with the city.

How do you know your concrete needs cutting?

Most folks don't think about cutting until another job depends on it, like a new drain, a window or a fresh pour. These are the things that usually tell you a saw is the right tool.

  • One driveway panel has cracked and dropped while the rest sits fine, so a saw cut frees just that piece.

  • Water pools on your garage floor or basement slab, and a trench for a drain line would carry it off.

  • A plumber needs a new line under the slab, which usually means a sawed trench or a cored hole.

  • You want a window or doorway in a concrete wall, and a hammer would leave ragged, cracked edges.

  • A new walk has to meet your old patio, and its chipped edge needs a clean saw line first.

  • A raised sidewalk slab keeps tripping people, and cutting it out beats breaking up the whole run.

Call as soon as you know a plumber, a window installer or a new pour is coming, because the cutting has to happen before they can start.

What happens when you call us for concrete cutting in Austin?

Here's how a cutting job runs with us, from the first call to the walk-through, and where the state's rules about digging and cutting water fit into it.

  1. Call and describe the cut

    I still answer the phone myself, and I'll set a time to come see the slab or wall in person, here in Austin or in Albert Lea, Stewartville, Kasson and the cities around them. If a plumber or installer has already marked where they need the opening, leave those marks up for me.

  2. I measure and write it up

    I measure the cut, check how thick the concrete is and whether there's steel in it, and talk through the approach that fits your job. You get a written estimate that spells out each part of the work, so you know what you're paying for and can compare it fairly.

  3. We line up locates and permits

    Once you say go, we line up utility locates, permits and inspections where they're needed and set the cutting day. If digging goes with the cut, Minnesota law requires whoever digs to notify the state's notification center at least 48 hours ahead, not counting that day, weekends or holidays, and no more than 14 calendar days out.

  4. We cut, clean up and walk through

    I'm on site with our crew through the last cut, and the gray slurry from sawing has to be caught and cleaned up rather than hosed into the street, because Minnesota stormwater guidance says it can't go into any waterway. Before we pack up, we walk the job with you and go over how to look after it.

Get a written concrete cutting estimate

Send the form and we'll get back to you within one business day to set a time for me to come out. The on-site estimate is free, with no obligation, and you get it in writing.

Hours
Mon–Fri: 7 AM–11 PM, Sat–Sun: 8 AM–10 PM

Slab thickness, steel and dust on a cutting job

Most house slabs we see, like driveways, patios and garage floors, are a few inches thick, and many have rebar, steel bars set in the concrete to hold it together once it cracks, or wire mesh doing the same job. Thicker concrete and more steel mean a slower cut and a bigger saw, and walls and foundations usually carry more steel than flatwork, the flat slabs around a house.

Some folks ask whether we can just bust the bad section out with a breaker. You can, and it can cost less up front, but it chips and cracks the slab you're keeping, so I'd rather saw a clean line for anything we're pouring against. The new piece also needs its subgrade, the dirt it sits on, dug out and packed, or it settles away from the old slab.

Cutting throws off dust with crystalline silica in it, and water on the blade cuts that dust way down, which matters most in a basement or garage. For indoor work, one trade group's specification says engine-powered saws need good ventilation, provided by the owner or the contractor, and it lists electric, hydraulic and air-powered saws as other options, so it's fair to ask which one we're bringing.

Concrete cutting questions we hear in Austin

How much does concrete cutting cost in Austin, MN?

Concrete saw cutting across the US usually runs about $4 to $25 per linear foot, and that's for the sawing alone. Reinforced or deeper slabs land higher per foot than an easy-to-reach 4- to 6-inch slab, and on a small job a minimum or trip charge for bringing the crew and saw out can matter more than the per-foot rate. Your written estimate gives you your own number.

Does concrete cutting include removing and hauling the concrete away?

Not always, because sawing and removal are separate jobs, and some cutters saw the lines and leave the panels right where they sit. Breaking, lifting, hauling and disposal can add more than the sawing itself, so compare quotes on what each one includes. Ours shows the sawing and any removal on separate lines, so you can see both.

What is the best way to cut a concrete wall or floor?

The best way depends on what you're cutting, how thick it is and how much steel is in it. Flat saws cut floor slabs, wall saws cut walls, hand saws reach tight spots and wire saws handle thick or heavily reinforced sections, while a core drill makes round holes for pipes, drains and conduit. I'll tell you which one fits once I've seen yours.

How do I find out what's inside a concrete slab before cutting it?

Have it scanned, which is what we do before the first cut on a slab or wall. Ground penetrating radar is an accepted, routine way to see what's set in concrete without harming it, and the scan shows where steel, pipes or conduit sit so the cut lines can be planned around them.

Where do I apply for a building permit in Austin, MN?

You apply with the Austin Building Department, and the city requires a building permit for any alteration or addition to an existing building or structure. No work can start until the city's Building Official approves it, so your start date follows that approval. If it isn't clear whether your cut needs a permit, I call and ask before we start.

What license does a concrete contractor need in Minnesota?

A contractor doing work in more than one special skill for the owner of a one- to four-unit home needs a state residential building contractor or remodeler license. A contractor offering just one specialty without that license falls under the state's Contractor Registration Program instead. We're licensed and insured, and I'm happy to talk through which one applies to your job.

Tell us where the cut goes

Call (507) 509-6215, email projects@concretecompanyaustin.com or use the estimate form with where the cut is, whether it's a wall or floor, its rough length and whether you want removal, so I show up knowing what to measure.

Mon–Fri: 7 AM–11 PM, Sat–Sun: 8 AM–10 PM

(507) 509-6215Request an estimate